Task 42
Task 42
SHC Task 42

Compact Thermal Energy Storage

Publications

| Advanced Search | Clear

The following are publications developed under Task 42:

General Task Publications

Compact Thermal Energy Storage: Material Development for System Integration
Compact Thermal Energy Storage: Material Development for System Integration
Technology Position Paper
August 2015 - PDF 0.2MB - Posted: 2015-08-10
By: IEA SHC Task 42: Compact Thermal Energy Storage, Matthias Rommel

This position paper explains the potential, the present status of development and the market status of compact thermal energy storages. Its aim is to inform policy makers, decision makers and opinion makers about the technologies and to discuss the technological and non-technological barriers and the actions needed to accelerate the development and market uptake of these very important technologies.

Deliverables

Task 42 Annex 29 Position Paper and All Final Deliverable Papers
Task 42 Annex 29 Position Paper and All Final Deliverable Papers
March 2016 - PDF 4.76MB - Posted: 2016-03-22
By: Matthias Rommel, Andreas Hauer, Wim Van Helden
Collection of the Position Paper and all final deliverable papers of the joint task IEA SHC Task 42 and IEA ECES Annex 29. The papers were presented at the SHC Conference 2015, December 2-4 Istanbul, Turkey. They will be published in the proceedings of this conference in due time.
Standard to determine the heat storage capacity of PCM using hf-DSC with constant heating/cooling rate (dynamic mode)
Standard to determine the heat storage capacity of PCM using hf-DSC with constant heating/cooling rate (dynamic mode)
A technical report of subtask A2.1 of IEA-SHC 42 / ECES Annex 29
January 2015 - PDF 0.75MB - Posted: 2015-05-26
By: Stefan Gschwander, Thomas Haussmann, Georg Hagelstein, Aran Sole, Gonzalo Diarce, Wolfgang Hohenauer, Daniel Lager, Christoph Rathgeber, Peter Hennemann, Ana Lazaro, Harald Mehling
The measurement procedure defined in this document is based on the already existing standard RAL-GZ 896 page (www.PCM-RAL.de). The T4229 is extending the procedure for PCM-characterization using DSCs by: • Definition for the calibration of the DSC • Definitions/suggestion for the sample preparation • Detailed description for the measurement • Suggestion for the improvement of the measurement results (analyzes/evaluation)
Designing a Thermal Storage Device - Flowchart
Designing a Thermal Storage Device - Flowchart
September 2013 - PDF 0.07MB - Posted: 2013-09-16
By: Task 42
Task 4224 - Designing a Thermal Storage Device - Flowchart
Development of Space Heating and Domestic Hot Water Systems with Compact Thermal Energy Storage
Development of Space Heating and Domestic Hot Water Systems with Compact Thermal Energy Storage
July 2013 - PDF 2.28MB - Posted: 2014-05-03
By: Jane H. Davidson, Josh Quinnell, Jay Burch, USA H.A. Zondag, Robert de Boer, Christian Finck, Ruud Cuypers, The Netherlands Luisa F. Cabeza, Spain Andreas Heinz, Dagmar Jahnig, Austria Simon Furbo, Denmark Florian Bertsch, Germany
Long-term, compact thermal energy storage (TES) is essential to the development of cost-effective solar and passive building-integrated space heating systems and may enhance the annual technical and economic performance of solar domestic hot water (DHW) systems. Systems should provide high energy storage density, charge and discharge temperatures that match the heat source used for charging and the intended load, adequate charge/discharge power, and employ storage materials that are stable over many cycles, non-toxic, environmentally safe. Moreover, these systems must compete effectively in the marketplace and therefore should provide an economic benefit compared to conventional heating and DHW systems, which have traditionally relied on sensible water storage.
Collection of experimental data on the behavior of TCM/PCM-materials to benchmark numerical codes
Collection of experimental data on the behavior of TCM/PCM-materials to benchmark numerical codes
December 2012 - PDF 2.19MB - Posted: 2014-05-03
By: Paul Gantenbein & Camilo Rindt
The activities in this working group are aimed at developing and testing numerical models that help to understand and optimise the material behaviour and the dynamic behaviour of compact thermal energy storage systems and components based on Phase Change Materials (PCM’s) and Thermo Chemical Materials (TCM’s). Ultimately, these numerical models could help to find ways to optimise the materials in combination with the system components. The activities in this working group help to lay the foundation for such models.
Modeling techniques of TCM/PCM-materials on micro-, meso- and macro scales
Modeling techniques of TCM/PCM-materials on micro-, meso- and macro scales
April 2011 - PDF 1.43MB - Posted: 2014-05-03
By: Paul Gantenbein & Camilo Rindt
In the Task 4224, a large group of thermal energy storage experts collaborated with the aim to further develop materials for compact thermal energy storage and systems for the integration of compact thermal energy storage in heating or cooling systems. The activities were performed from 2009 until the end of 2012 and were divided in working groups, according to the structure depicted here. The groups worked on a number of deliverables, that are condensed into reports.
Development of a Test Standard for PCM and TCM Characterization
Development of a Test Standard for PCM and TCM Characterization
Part 1: Characterization of Phase Change Materials
April 2011 - PDF 3.01MB - Posted: 2015-05-26
By: Stefan Gschwander, Ana Lazaro, Luisa F. Cabeza, Eva Günther, Magali Fois, Justin Chui
As the knowledge of the behavior of heat storage materials is very essential to design an application it is important to characterize these materials. The important characteristics of heat storage materials are their heat capacity, the thermal conductivity, the density and viscosity all in dependency on temperature. All these parameters are necessary to size a thermal storage or to develop heat exchanger to charge and discharge such storages. Simulations are also very often used to analyze applications or components of it and their interaction with the storage material. Such simulations will not be valid if the used material data is not describing its behavior in a correct way, so also for this purpose good and reliable results from the characterization are needed.

Sensible Storage

Selection of Materials with Potential in Sensible Thermal Energy Storage
October 2010 - Posted: 2012-11-05
By: Fernández AI, Martínez M, Segarra M, Martorell I, Cabeza LF

Phase Change Materials

Microencapsulation of Salts for Enhanced Thermochemical Storage Materials
December 2012 - Posted: 2013-03-08
By: R. Cuypers, A.J. de Jong, J. Eversdijk, H. van ‘t Spijker, H. Oversloot, B.L.J. Ingenhut, R.K.H. Cremers, and N.E. Papen-Botterhuis
Composite material for heat storage, method for preparation and use
December 2012 - Posted: 2013-03-08
By: R. Cuypers, A.J. de Jong, J. Eversdijk, H. Oversloot, H. van ‘t Spijker, N.E. Papen-Botterhuis
Intercomparative tests on phase change materials characterisation with differential scanning calorimeter
Intercomparative tests on phase change materials characterisation with differential scanning calorimeter
November 2012 - PDF 0.74MB - Posted: 2013-01-25
By: Ana Lazaro, Conchita Peñalosa, Aran Solé, Gonzalo Diarce, Thomas Haussmann, Magali Fois, Belén Zalba, Stefan Gshwander, Luisa F. Cabeza
Publisher: Applied Energy Journal

For the correct design of thermal storage systems using phase change materials (PCMs) in any application, as well as for their simulation, it is essential to characterise the materials from thermophysical and rheological standpoints (phase change enthalpy, thermal conductivity in solid and liquid phases, viscosity and density in function of temperature). Taking advantage of the different research groups facilities available in two international networks: within the IEA (International Energy Agency), the ECES Implementing Agreement (Energy Conservation through Energy Storage IA) and SHC Programme (Solar Heating and Cooling) Task 42/Annex 24 ‘‘Compact Thermal Energy Storage – Material Development for System Integration’’, and the COST Action TU0802 ‘‘Next generation cost effective phase change materials for increased energy efficiency in renewable energy systems in buildings (NeCoE-PCM)’’ a set of Round Robin Tests (RRTs) was proposed.

Influence of the Experimental Conditions on the Subcooling of Glauber's Salt When Used as PCM, Solar Energy Materials And Solar Cells
July 2012 - Posted: 2012-11-05
By: A. García-Romero, G. Diarce, J. Ibarretxe, A. Urresti, J.M. Sala,
Improving Thermal Performance of Freezers Using Phase Change Materials
June 2012 - Posted: 2012-11-05
By: Oró E, Miró L, Farid MM, Cabeza LF
Evaluation of the Environmental Impact of Experimental Cubicles Using Life Cycle Assessment: A Highlight on the Manufacturing Phase
April 2012 - Posted: 2012-11-05
By: Menoufi K, Castell A, Boer D, Perez G, Navarro L, Cabeza LF
Use of Microencapsulated PCM in Buildings and the Effect of Adding Awnings
January 2012 - Posted: 2012-11-05
By: Arce P, Castellón C, Castell A, Cabeza LF
Analysis of Implementing Phase Change Materials in Open-Air Swimming Pools
January 2012 - Posted: 2012-11-05
By: Zsembinszki G, Farid MM, Cabeza LF
Thermal Analysis of Including Phase Change Material in a Domestic Hot Water Cylinder
December 2011 - Posted: 2012-11-05
By: de Gracia A, Oró E, Farid MM, Cabeza LF
New Equipment for Testing Steady and Transient Thermal Performance of Multilayered Building Envelopes with PCM
December 2011 - Posted: 2012-11-05
By: de Gracia A, Barreneche C, Farid MM, Cabeza LF
Behaviour of Green Facades in Mediterranean Continental Climate
April 2011 - Posted: 2012-11-05
By: Pérez G, Rincón L, Vila A, González JM, Cabeza LF
Materials Used as PCM in Thermal Energy Storage In Buildings: A Review
April 2011 - Posted: 2012-11-05
By: Cabeza LF, Castell A, Barreneche C, de Gracia A, Fernández AI
Effect of Microencapsulated Phase Change Material in Sandwich Panels
October 2010 - Posted: 2012-11-05
By: Castellón C, Medrano M, Roca J, Cabeza LF, Navarro ME, Fernández AI, Lázaro A, Zalba B
Life Cycle Assessment of the Inclusion of Phase Change Materials (PCM) in Experimental Buildings
September 2010 - Posted: 2012-11-05
By: De Gracia A, Rincón L, Castell A, Jiménez M, Boer D, Medrano M, Cabeza LF
Compatibility of Plastic with Phase Change Materials (PCM)
June 2010 - Posted: 2012-11-05
By: Castellón C, Martorell I, Cabeza LF, Fernández AI, Manich AM
Document Number: 10.1002/er.1723
Experimental Study of Using PCM in Brick Constructive Solutions for Passive Cooling
April 2010 - Posted: 2012-11-05
By: Castell A, Medrano M, Martorell I, Pérez G, Cabeza LF
Poly(2-Alkyloyloxyethylacrylate) and Poly(2-Alkyloyloxyethylacrylate-Co-Methylacrylate) Comb-Like Polymers as Novel Phase Change Materials for Thermal Energy Storage - Posted: 2012-11-05
By: Cemil Alkan*, Ömer Faruk Ensari, Derya Kahraman
Experimental Studies on Seasonal Heat Storage Based on Stable Supercooling of a Sodium Acetate Water Mixture - Posted: 2012-11-05
By: Simon Furbo, Janne Dragsted, Jianhua Fan, Ziqian Chen, Elsa Andersen and Bengt Perers
Publisher: Technical University of Denmark

Sorption and Thermochemical Materials

Molecular dynamics simulation of heat transfer through a water layer between two platinum slabs
September 2012 - Posted: 2012-11-25
By: E. Iype E. Arlemark S.V. Nedea C.C.M. Rindt H.A. Zondag
Publisher: Proceedings of the 6th European Thermal Sciences Conference (Eurotherm 2012)
DFT Study on Characterization of Hydrogen Bonds in the Hydrates of MgSO4
August 2012 - Posted: 2012-11-25
By: Eldhose Iype, Silvia V. Nedea, Camilo C. M. Rindt , Anton A. van Steenhoven, Herbert A. Zondag , and A. P. J. Jansen
Publisher: Copyright © 2012 American Chemical Society
Document Number: 10.1021/jp3025649
Order
Magnesium salt hydrates are potential thermo-chemical energy storage materials considering its high energy storage density and its availability. However, in practical applications, these materials suffers from low efficiency due to their sluggish kinetics and significant structural changes during hydration and dehydration. A DFT PW91-TZ2P level optimization is performed on the various hydrates of magnesium sulfate molecules to study their structural properties. The study identifies a wide network of hydrogen bonds which is significantly influencing the chemical structure of the molecules. These hydrogen bonds appear to cause distortions in the hydrated structures and even hindering the coordination of water with magnesium resulting in lower energy isomers. In the case of hexa-hydrated isomers, the hydrogen bond stabilizes a conformation which has only four coordinated water molecules, and is energetically more stable than the conformation with six coordinated water molecules. The sluggish hydration kinetics in magnesium sulfate is attributed to the strong hydrogen bond network present in the crystals. In addition, the hexahydrated structure exhibits an intra-molecular proton transfer reaction. This suggests that the strong hydrogen bond interactions potentially dissociates water molecules during hydration.
Adsorption properties of porous materials for solar thermal energy storage and heat pump applications
SHC 2012
July 2012 - PDF 0.21MB - Posted: 2012-11-14
By: J. Jänchen, H. Stach
The water adsorption properties of modified porous sorbents for solar thermal energy storage and heat transformation have been investigated by thermogravimetry (TG) differential thermogravimetry (DTG), microcalorimetry, measurements of water adsorption isotherms, and storage tests. A chabazite type SAPO, a dealuminated faujasite type zeolite, and a mesostructured aluminosilicate, have been synthesized and compared with common zeolites X, Y and silica gel. It has been found that optimized lattice composition and pore architecture contribute to well adapt hydrophilic properties and a beneficial steep isotherm.
Development of a Seasonal Thermochemical Storage System
Proceedings of the (1st International Conference on Solar Heating and Cooling for Buildings and Industry 2012, San Francisco, USA, 9-11 july 2012
July 2012 - Posted: 2013-03-08
By: R. Cuypers, N. Maraz, J. Eversdijk, C. Finck, E. Henquet, H. Oversloot, H. van ‘t Spijker, A. de Geus
Publisher: Energy Procedia
New two-component water sorbent CaCl2-FeKIL2 for solar thermal energy storage
July 2012 - PDF 1MB - Posted: 2012-11-15
By: Alenka Ristic, Darja Maucec, Stefan K. Henninger, Venceslav Kaucic
Publisher: Microporous and Mesoporous Materials
A new two-component (composite) water sorbent CaCl2-FeKIL2 has been developed for sorption-based solar thermal energy storage. The matrix of the composite is FeKIL2 material with disordered mesopores, high surface area of 712 m2/g and mesopore dimensions between 4 and 29 nm. The composite, prepared by wet impregnation of FeKIL2 with CaCl2, has lower surface area (418 m2/g) and similar mesopore dimensions as the matrix. The maximum water sorption capacity of FeKIL2 is 0.21 g/g, while the composite possesses 3 times higher maximum water sorption capacity due to the presence of the salt in the matrix. Heat of adsorption of the composite is 50.4 kJ/mol. A short-term cycling test between temperatures of 150 and 40 C at a water vapour pressure of 5.6 kPa confirms a comparatively good hydrothermal stability of the composite.
MERITS: More Effective use of Renewables Including compact seasonal Thermal energy Storage
InnoStock Conference 2012, Lleida, Spain, 16-18 May 2012
May 2012 - Posted: 2013-03-08
By: R. Cuypers, C. Finck, E. Henquet, H. Oversloot, A. de Geus
Performance analysis of an atmospheric packed bed thermo-chemical heat storage system
May 2012 - Posted: 2012-11-25
By: Beek, T.J.J. van, Rindt, C.C.M. & Zondag, H.A.
Characterization of the sorption process in thermochemical materials for seasonal solar heat storage application
May 2012 - Posted: 2012-11-25
By: Ferchaud, C., Zondag, H.A., Boer, R. de & Rindt, C.C.M.
Preparation, hydrothermal stability and thermal adsorption storage properties of binderless zeolite beads
International Journal of Low-Carbon Technologies Advance Access published May 5, 2012
May 2012 - PDF 0.39MB - Posted: 2012-11-14
By: Jochen Janchen, Kristin Schumann, Erik Thrun, Alfons Brandt, Baldur Unger and Udo Hellwig
Novel binderless zeolite beads of types A and X have been synthesized and characterized by scanning electron microscopy, mercury intrusion, nitrogen adsorption, thermogravimetry, water adsorption isotherm measurements, cyclic hydrothermal treatments and storage tests. The binderless molecular sieves show an improved adsorption capacity, sufficient hydrothermal stability, higher specific energies and the potential for a better performance density of the storage. Both open and closed storage tests have shown comparable adsorption capacities and specific energies for the binderless molecular sieves. A significantly higher discharging temperature, however, could be realized with the open storage system.
The Performance of Small-Pore Microporous Aluminophosphates in Low-Temperature Solar Energy Storage
The Structure-Property Relationship
February 2012 - Posted: 2012-11-05
By: Dr. Alenka Ristic, prof. Nataša Zabukovec Logar, prof. Venceslav Kaucic in collaboration with Dr. Stefan Henninger
Publisher: National Institute of Chemistry Slovenia / Fraunhofer Institute
Quantum chemical analysis of the structures of MgSO4 hydrates
2012 - Posted: 2012-11-25
By: Iype, E., Ozen, C., Gaastra - Nedea, S.V., Rindt, C.C.M. & Zondag, H.A.
Minimization of the Environmental Impact of Chrome Tanning: A New Process Reusing the Tanning Floats
November 2011 - Posted: 2012-11-05
By: Morera JM, Bartolí E, Chico R, Solé C, Cabeza LF
Process and Reactor Design for Thermo-Chemical Energy Stores
August 2011 - PDF 0.77MB - Posted: 2012-11-05
By: Barbara Mette, Henner Kerskes, Harald Druck
Publisher: University of Stuttgart, Institute for Thermodynamics and Thermal Engineering (ITW)
Development of a Thermo-Chemical Energy Storage for Solar Thermal Applications
August 2011 - PDF 0.77MB - Posted: 2012-11-05
By: H.Kerskes, B.Mette, F.Bertsch, S.Asenbeck, H.Drück
Publisher: Research and Testing Centre for Thermal Solar Systems (TZS)
Exergy Analysis of Multi-Effect Water-LiBr Absorption Systems: From Half to Triple Effect
August 2010 - Posted: 2012-11-05
By: Gebreslassie BH, Medrano M, Boer D
Optimum Heat Exchanger Area Estimation Using Coefficients of Structural Bonds: Application to an Absorption Chiller
May 2010 - Posted: 2012-11-05
By: Gebreslassie BH, Medrano M, Mendes F, Boer D
Characterization of MgSO4 Hydrate for Thermochemical Seasonal Heat Storage
2009 - Posted: 2012-11-25
By: V.M. van Essen H.A. Zondag J. Cot Gores L.P.J. Bleijendaal M. Bakker R. Schuitema W.G.J. van Helden Z. He C.C.M. Rindt
Publisher: Journal of Solar Energy Engineering, Vol. 131(2009)
Document Number: p. 041014-1/7
Water vapor sorption in salt hydrates is one of the most promising means for compact, low loss, and long-term storage of solar heat in the built environment. One of the most interesting salt hydrates for compact seasonal heat storage is magnesium sulfate heptahydrate (MgSO4·7H2O). This paper describes the characterization of MgSO4·7H2O to examine its suitability for application in a seasonal heat storage system for the built environment. Both charging (dehydration) and discharging (hydration) behaviors of the material were studied using thermogravimetric differential scanning calorimetry, X-ray diffraction, particle distribution measurements, and scanning electron microscope. The experimental results show that MgSO4·7H2O can be dehydrated at temperatures below 150°C, which can be reached by a medium temperature (vacuum tube) collector. Additionally, the material was able to store 2.2 GJ/m3, almost nine times more energy than can be stored in water as sensible heat. On the other hand, the experimental results indicate that the release of the stored heat is more difficult. The amount of water taken up and the energy released by the material turned out to be strongly dependent on the water vapor pressure, temperature, and the total system pressure. The results of this study indicate that the application of MgSO4·7H2O at atmospheric pressure is problematic for a heat storage system where heat is released above 40°C using a water vapor pressure of 1.3 kPa. However, first experiments performed in a closed system at low pressure indicate that a small amount of heat can be released at 50°C and a water vapor pressure of 1.3 kPa. If a heat storage system has to operate at atmospheric pressure, then the application of MgSO4·7H2O for seasonal heat storage is possible for space heating operating at 25°C and a water vapor pressure of 2.1 kPa.
Thermochemical Storage Materials Research - Tga/Dsc-Hydration Studies
PDF 0.4MB - Posted: 2012-11-05
By: Opel, O., Rammelberg, H.U., Gérard, M., Ruck, W.
Publisher: Institute of Environmental Chemistry, Faculty Sustainability, Leuphana University of Lueneburg

Systems

Use of Rubber Crumbs as Drainage Layer in Green Roofs as Potential Energy Improvement Material
September 2012 - Posted: 2012-11-06
By: Pérez G, Vila A, Rincón L, Solé C, Cabeza LF
Comparative Life Cycle Assessment of Thermal Energy Storage Systems For Solar Power Plants
August 2012 - Posted: 2012-11-06
By: Oró E, Gil A, de Gracia A, Boer D, Cabeza LF
Use of Rubber Crumbs as Drainage Layer in Experimental Green Roofs
February 2012 - Posted: 2012-11-05
By: Vila A, Pérez G, Solé C, Fernández AI, Cabeza LF
Green Vertical Systems for Buildings as Passive Systems for Energy Savings
December 2011 - Posted: 2012-11-06
By: Pérez G, Rincón L, Vila A, González JM, Cabeza LF
Maximization of Heat Transfer in a Coil in Tank PCM Cold Storage System
November 2011 - Posted: 2012-11-06
By: Castell A, Belusko M, Bruno F, Cabeza LF
Energetic and Economic Aspects of Seasonal Heat Storage in Single and Multifamily Houses
October 2011 - PDF 0.21MB - Posted: 2012-11-06
By: Henner Kerskes, Harald Drück
Publisher: Institute for Thermodynamics and Thermal Engineering (ITW) Research and Testing Centre for Thermal Solar Systems (TZS)
Dynamic Thermal Performance of Alveolar Brick Construction System
July 2011 - Posted: 2012-11-06
By: de Gracia A, Castell A, Medrano M, Cabeza LF
Design and Performance of Energy-Efficient Solar Residential House In Andorra
April 2011 - Posted: 2012-11-06
By: Llovera J, Potau X, Medrano M, Cabeza LF
Dimensionless Numbers Used to Characterize Stratification in Water Tanks for Discharging at Low Flow Rates
October 2010 - Posted: 2012-11-06
By: Castell A, Medrano M, Solé C, Cabeza LF
Solar Seasonal Store
September 2010 - Posted: 2012-11-06
By: Philip Griffiths
Experimental and Numerical Investigations on Thermo-Chemical Heat Storage
September 2010 - PDF 0.31MB - Posted: 2012-11-06
By: Henner Kerskes, Barbara Mette, Sebastian Asenbeck, Harald Drück and Hans Müller-Steinhagen
Experimental Study on the Performance of Insulation Materials in Mediterranean Construction
May 2010 - Posted: 2012-11-05
By: Cabeza LF, Castell A, Medrano M, Martorell I, Pérez G, Fernández I
State of the Art on High Temperature Thermal Energy Storage for Power Generation
Part 1 - Concepts, Materials and Modellization
January 2010 - Posted: 2012-11-06
By: Gil A, Medrano M, Martorell I, Lázaro A, Dolado P, Zalba B, Cabeza LF
State of the Art on High-Temperature Thermal Energy Storage for Power Generation
Part 2 - Case Studies
January 2010 - Posted: 2012-11-06
By: Medrano M, Gil A, Martorell I, Potau X, Cabeza LF
Heat Transfer Efficient Thermal Energy Storage for Steam Generation
September 2009 - PDF 0.98MB - Posted: 2012-11-05
By: Michael Epstein
Publisher: Weizmann Institute of Science
Sensible Heat Storage in District Heating Networks: A Novel Control Strategy Using the Network as Storage
PDF 0.13MB - Posted: 2012-11-05
By: D. Basciotti, F. Judex, O., R.R. Schmidt
Publisher: Austrian Institute of Technology
Heat Transfer Capacity of a Heat Exchanger Module for Seasonal Heat Storage - Posted: 2012-11-05
By: Jianhua Fan, Simon Furbo, Ziqian Chen, Elsa Andersen and Bengt Perers
Publisher: Technical University of Denmark
A Theoretical Study of the Impact of Using Small Scale Thermo Chemical Storage Units in District Heating Networks
PDF 0.16MB - Posted: 2012-11-05
By: D. Basciotti and O. Pol.
Publisher: Austrian Institute of Technology

Other

Articles

Task 42: Compact Thermal Energy Storage
Task 42: Compact Thermal Energy Storage
Collaboration Leads to Groundbreaking Work
May 2016 - PDF 0.68MB - Posted: 2016-05-25
By: Matthias Rommel
For the first time international teams of materials experts and application experts collaborated to tackle together issues confronting thermal energy storage. This one of a kind research platform was created jointly by the IEA Solar Heating and Cooling Programme (IEA SHC) and the IEA Energy Conservation through Energy Storage Programme (IEA ECES).

Highlights

Task 42 Highlights 2013
Task 42 Highlights 2013
Thermal Energy Storage: Material Development for System Integration
February 2014 - PDF 0.2MB - Posted: 2014-03-05
To reach high solar fractions, it is necessary to store heat or cold efficiently for longer periods of time. At this time, there are no cost-effective compact storage technologies available. For high solar fraction systems, hot water stores are expensive and require very large volumes of space. Alternative storage technologies, such as phase change materials (PCMs), sorption materials and thermochemical materials (TCMs) are only available at the laboratory scale, and more R&D is needed before they are available commercially.
Task 42 Highlights 2012
Task 42 Highlights 2012
February 2013 - PDF 3.28MB - Posted: 2013-02-12

To reach high solar fractions, it is necessary to store heat or cold efficiently for longer periods of time. At this time, there are no cost-effective compact storage technologies available. For high solar fraction systems, hot water stores are expensive and require very large volumes of space. Alternative storage technologies, such as phase change materials (PCMs), sorption materials and thermochemical materials (TCMs) are only available at the laboratory scale, and more R&D is needed before they are available commercially.

Presentations

Enthalpy and temperature of the phase change solid–liquid
An analysis of data of compounds employing entropy
September 2013 - Posted: 2013-09-13
By: Harald Mehling (ZAE Wuerzburg, Germany)
Review of Solar Thermal Storage Techniques and Associated Heat Transfer Technologies
February 2012 - Posted: 2012-11-06
By: Cabeza LF, Solé C, Castell A, Oró E, Gil A
Overview of Thermal Energy Storage (TES) Potential Energy Savings and Climate Change Mitigation Ii Spain and Europe
August 2011 - Posted: 2012-11-06
By: Arce P, Medrano M, Gil A, Oro E, Cabeza LF
Economic Viability of a Molten Carbonate Fuel Cell Working with Biogas
October 2010 - Posted: 2012-11-06
By: Castell A, Margalef P, Medrano M, Cabeza LF, Samuelsen S
Economic Viability of Using Biogas from Tannery Wastes in Molten Carbonate Fuel Cells
May 2010 - Posted: 2012-11-06
By: Castell A, Medrano M, Cabeza LF, Morera JM, Bartolí E
Austrian Masterplan - Thermal Energy Storage
PDF 0.25MB - Posted: 2012-11-06
By: Bernhard Zettl, Andreas Heinz, Philip Ohnewein, Michael Monsberger, Stefan Vorbach and Wim van Helden
Publisher: Austria Solar Innovation Center